Infiniti (1990-25)
WARNING: |
Accidental air bag deployment is possible. Personal
injury may result. Avoid area near steering wheel and instrument
panel even if air bags have deployed. Dual-stage air bag modules
may be present that could contain an undeployed stage. When disposing
of a deployed dual-stage air bag, always treat it as a |
Application | Year | Type | Table |
EX35 | 2008-12 | D/P2, HI, SI, WP | Infiniti-8 |
EX37 | 2013 | D/P2, HI, SI, WP | Infiniti-15 |
FX35 | 2009-12 | D/P2, HI, SI, WP | Infiniti-10 |
FX35 | 2006-08 | D/P2, HI, SI, WP | Infiniti-7 |
2003-05 | D/P2, HI, SI, WP | Infiniti-4 | |
FX37 | 2013 | D/P2, HI, SI, WP | Infiniti-12 |
FX45 | 2006-08 | D/P2, HI, SI, WP | Infiniti-10 |
FX50 | 2009-13 | D/P2, HI, SI, WP | Infiniti-10 |
2003-05 | D/P2, HI, SI, WP | Infiniti-4 | |
G20 | 1999-02 | D/P2, SI | Infiniti-1 |
1993-96 | D/P | Infiniti-2 | |
G25 | 2011-12 | D/P2, HI, SI, WP | Infiniti-9 |
G35 | 2006-08 | D/P2, HI, SI, WP | Infiniti-7 |
2003-05 | D/P2, HI, SI, WP | Infiniti-1 | |
G37 Convertible | 2009-13 | D/P2, HI, SI, WP | Infiniti-9 |
G37 Coupe | 2008-13 | D/P2, HI, SI, WP | Infiniti-9 |
G37 Sedan | 2009-13 | D/P2, HI, SI, WP | Infiniti-9 |
I30 | 2001 | D/P2, SI, WP | Infiniti-1 |
1998-00 | D/P, SI | Infiniti-1 | |
1997 | D/P | Infiniti-1 | |
1996 | D/P | Infiniti-2 | |
I35 | 2002-04 | D/P2, SI, WP | Infiniti-1 |
J30 | 1997 | D/P | Infiniti-1 |
1994-96 | D/P | Infiniti-2 | |
1993 | D/P | Infiniti-3 | |
JX35 | 2013 | D/P2, HI, SI | Infiniti-14 |
M30 | 1990-92 | DS | Infiniti-3 |
M35 | 2006-10 | D/P2, HI, SI, WP | Infiniti-7 |
M35h | 2012 | D/P2, HI, SI, WP | Infiniti-11 |
M Hybrid | 2013 | D/P2, HI, SI, WP | Infiniti-13 |
M37 | 2011-13 | D/P2, HI, SI, WP | Infiniti-11 |
M37x | 2011 | D/P2, HI, SI, WP | Infiniti-11 |
M45 | 2006-10 | D/P2, HI, SI, WP | Infiniti-7 |
M56 | 2011-13 | D/P2, HI, SI, WP | Infiniti-11 |
2003-04 | D/P2, HI, SI | Infiniti-5 | |
Q40 | 2015 | D/P2, HI, SI | Infiniti-18 |
Q45 | 2006 | D/P2, HI, SI, WP | Infiniti-7 |
2002-05 | D/P2, HI, SI, WP | Infiniti-1 | |
1998-01 | D/P, SI | Infiniti-1 | |
1997 | D/P | Infiniti-1 | |
1994-96 | D/P | Infiniti-2 | |
1990-93 | DS | Infiniti-3 | |
Q50 | 2023-24 | D/P2, HI, SI, KI | Infiniti-25 |
2017-22 | D/P2, HI, SI | Infiniti-21 | |
2014-16 | D/P2, HI, SI | Infiniti-16 | |
Q50 Hybrid | 2017-18 | D/P2, HI, SI | Infiniti-21 |
2014-16 | D/P2, HI, SI | Infiniti-16 | |
Q60 Convertible | 2014-15 | D/P2, HI, SI | Infiniti-17 |
Q60 Coupe | 2019-22 | D/P2, HI, SI, WP | Infiniti-22 |
2017-18 | D/P2, HI, SI, WP | Infiniti-19 | |
2014-16 | D/P2, HI, SI, WP | Infiniti-16 | |
Q70 | 2019 | D/P2, HI, SI, WP | Infiniti-23 |
2014-18 | D/P2, HI, SI, WP | Infiniti-16 | |
Q70 Hybrid | 2014-18 | D/P2, HI, SI, WP | Infiniti-16 |
QX4 | 2000-03 | D/P, SI | Infiniti-1 |
1997-99 | D/P | Infiniti-1 | |
QX30 | 2019 | D/P2, HI, KI, SI | Infiniti-23 |
2017-18 | D/P2, HI, KI, SI | Infiniti-20 | |
QX50 | 2022-25 | D/P2, HI, SI, KI, WP | Infiniti-24 |
2019-21 | D/P2, HI, SI, WP | Infiniti-16 | |
2014-18 | D/P2, HI, SI, WP | Infiniti-16 | |
QX55 | 2023-25 | D/P2, HI, SI, KI, WP | Infiniti-26 |
QX55 | 2022 | D/P2, HI, SI, KI, WP | Infiniti-24 |
QX56 | 2005-13 | D/P2, HI, SI, WP | Infiniti-6 |
2004 | D/P2, HI, SI | Infiniti-6 | |
QX60 | 2022-24 | D/P2, HI, SI, KI, WP | Infiniti-24 |
2014-20 | D/P2, HI, SI | Infiniti-16 | |
QX60 Hybrid | 2014-19 | D/P2, HI, SI | Infiniti-16 |
QX70 | 2014-17 | D/P2, HI, SI, WP | Infiniti-16 |
QX80 | 2019-24 | D/P2, HI, SI, WP | Infiniti-23 |
2014-18 | D/P2, HI, SI, WP | Infiniti-16 | |
D/P—Driver’s & Passenger’s Side D/P2—Driver’s & Passenger’s Side (Dual-Stage) DS—Driver’s Side HI—Head Impact KI—Knee Impact SI—Side Impact PS2—Passenger’s Side (Dual-Stage) WP—Whiplash Protection
Replace after Deployment | Inspect & if Damaged, Replace Component (Even if Air Bag Did Not Deploy) | Comments | |||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
1On side of impact, including
inspection of seat slides and adjusters.
2Except 1997-99 QX4.
3Except 1996-98 I30 and 1997-99 QX4.
41999-02 G20, 1999-05 Q45, 2002-04 I35, 2000-03
QX4, 2003-05 G35, if side air bag deployed.
52003-05 G35
6Inspect all seat belt assemblies. Replace
all seat belt assemblies in use during a collision, unless collision
was minor and belts, retractors and buckles show no damage and continue
to operate properly. Inspect carefully for damage to anchor bolts,
guides and mounting points, as well as torn webbing and bent retractors, etc.
|
Replace after Deployment | Inspect & if Damaged, Replace Component (Even if Air Bag Did Not Deploy) | Comments | |||||||||||||||||||||||||||
|
|
|
|||||||||||||||||||||||||||
1Inspect all seat belt assemblies.
Replace all seat belt assemblies in use during a collision, unless
collision was minor and belts, retractors and buckles show no damage
and continue to operate properly. Inspect carefully for damage to
anchor bolts, guides and mounting points, as well as torn webbing
and bent retractors, etc.
|
Replace after Deployment | Inspect & if Damaged, Replace Component (Even if Air Bag Did Not Deploy) | Comments | |||||||||||||||||||||||||||
|
|
|
|||||||||||||||||||||||||||
1Inspect all seat belt assemblies.
Replace all seat belt assemblies in use during a collision, unless
collision was minor and belts, retractors and buckles show no damage
and continue to operate properly. Inspect carefully for damage to
anchor bolts, guides and mounting points, as well as torn webbing
and bent retractors, etc.
|
Replace after Deployment | Inspect & if Damaged, Replace Component (Even if Air Bag Did Not Deploy) | Comments | |||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
1Replace all parts of seat
back, including seat back frame, following side air bag deployment.
2Replace instrument panel following passenger’s
side air bag module deployment.
3Inspect all seat belt assemblies. Replace
all seat belt assemblies in use during a collision, unless collision
was minor and belts, retractors and buckles show no damage and continue
to operate properly. Inspect carefully for damage to anchor bolts,
guides and mounting points, as well as torn webbing and bent retractors, etc.
|
Replace after Deployment | Inspect & if Damaged, Replace Component (Even if Air Bag Did Not Deploy) | Comments | |||||||||||||||||||||||||||
|
|
|
|||||||||||||||||||||||||||
1Replace all parts of seat
back, including seat back frame, following side air bag deployment.
2Inspect all seat belt assemblies. Replace
all seat belt assemblies in use during a collision, unless collision
was minor and belts, retractors and buckles show no damage and continue
to operate properly. Inspect carefully for damage to anchor bolts,
guides and mounting points, as well as torn webbing and bent retractors, etc.
|
Replace after Deployment | Inspect & if Damaged, Replace Component (Even if Air Bag Did Not Deploy) | Comments | |||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
1Using new fasteners.
2Also referred to as diagnosis sensor unit.
Replace after any SRS component deploys.
3Following deployment of frontal air bag
modules.
4On the side of impact.
5Replace front seat back assembly following
deployment of side air bag.
6Following deployment of driver’s
side air bag module.
7Confirm seat belt pretensioner deployment
using CONSULT tester.
8Following deployment of passenger’s
side air bag module.
9Inspect all seat belt assemblies. Replace
all seat belt assemblies in use during a collision, unless collision
was minor and belts, retractors and buckles show no damage and continue
to operate properly. Inspect carefully for damage to anchor bolts,
guides and mounting points, as well as torn webbing and bent retractors, etc.
|
Replace after Deployment | Inspect & if Damaged, Replace Component (Even if Air Bag Did Not Deploy) | Comments | |||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
1If any of the front air bags
or seat belt pre-tensioners have been activated: REPLACE the crash
zone sensor and bracket with new fasteners.
2On the side of impact.
3Replace front seat back assembly following
deployment of side air bag.
4Repair center pillar inner if damaged.
5Following deployment of driver’s
side air bag module.
6If damaged following passenger’s
side air bag module deployment.
7Inspect all seat belt assemblies. Replace
all seat belt assemblies in use during a collision, unless collision
was minor and belts, retractors and buckles show no damage and continue
to operate properly. Inspect carefully for damage to anchor bolts,
guides and mounting points, as well as torn webbing and bent retractors, etc.
|
Replace after Deployment | Inspect & if Damaged, Replace Component (Even if Air Bag Did Not Deploy) | Comments | |||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
1Also referred to as diagnosis
sensor unit. Replace after any SRS component deploys.
2If any of the front air bags or seat belt
pre-tensioners have been activated: REPLACE the crash zone sensor
and bracket with new fasteners.
3On the side of impact.
4Replace front seat back assembly following
deployment of side air bag.
5Repair center pillar inner if damaged.
6Following deployment of driver’s
side air bag module.
7Following deployment of passenger’s
side air bag module, 2009-12 EX35. Inspect and replace if damaged
on 2008 EX35.
8Inspect all seat belt assemblies. Replace
all seat belt assemblies in use during a collision, unless collision
was minor and belts, retractors and buckles show no damage and continue
to operate properly. Inspect carefully for damage to anchor bolts,
guides and mounting points, as well as torn webbing and bent retractors, etc.
|
Replace after Deployment | Inspect & if Damaged, Replace Component (Even if Air Bag Did Not Deploy) | Comments | |||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
1Also referred to as diagnosis
sensor unit. Replace after any SRS component deploys.
2If any of the front air bags or seat belt
pre-tensioners have been activated: REPLACE the crash zone sensor
and bracket with new fasteners.
3On the side of impact.
4Replace front seat back assembly following
deployment of side air bag.
5Replace door finisher on models with door
mounted curtain air bag modules after deployment.
6Repair center pillar inner if damaged.
7Following deployment of driver’s
side air bag module.
8Following deployment of passenger’s
side air bag module on 2009-13 G37 convertible, coupe, & sedan.
On 2008 coupe, inspect and replace instrument panel if damaged after
passenger’s side air bag module deployment.
9Inspect all seat belt assemblies. Replace
all seat belt assemblies in use during a collision, unless collision
was minor and belts, retractors and buckles show no damage and continue
to operate properly. Inspect carefully for damage to anchor bolts,
guides and mounting points, as well as torn webbing and bent retractors, etc.
|
Replace after Deployment | Inspect & if Damaged, Replace Component (Even if Air Bag Did Not Deploy) | Comments | |||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
1Also referred to as diagnosis
sensor unit. Replace after any SRS component deploys.
2If any of the front air bags or seat belt
pre-tensioners have been activated: REPLACE the crash zone sensor
and bracket with new fasteners.
3On the side of impact.
4Replace front seat back assembly following
deployment of side air bag.
5Repair center pillar inner if damaged.
6Following deployment of driver’s
side air bag module.
7Following deployment of passenger’s
side air bag module on 2010-12 FX35 & FX50. On 2009 FX35 & FX50,
inspect and replace instrument panel if damaged after passenger’s
side air bag module deployment or if instrument panel is integrated
type.
8Inspect all seat belt assemblies. Replace
all seat belt assemblies in use during a collision, unless collision
was minor and belts, retractors and buckles show no damage and continue
to operate properly. Inspect carefully for damage to anchor bolts,
guides and mounting points, as well as torn webbing and bent retractors, etc.
|
Replace after Deployment | Inspect & if Damaged, Replace Component (Even if Air Bag Did Not Deploy) | Comments | |||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
1Using new fasteners.
2Also referred to as diagnosis sensor unit.
Replace after any SRS component deploys.
3If any of the front air bags or seat belt
pre-tensioners have been activated: REPLACE the crash zone sensor
and bracket with new fasteners.
4On the side of impact.
5Replace front seat back assembly following
deployment of side air bag.
6Repair center pillar inner if damaged.
7Following deployment of driver’s
side air bag module.
8Confirm seat belt pretensioner deployment
using CONSULT tester.
9Replace integrated type instrument panel
following passenger’s side air bag module deployment.
10Inspect all seat belt assemblies. Replace
all seat belt assemblies in use during a collision, unless collision
was minor and belts, retractors and buckles show no damage and continue
to operate properly. Inspect carefully for damage to anchor bolts,
guides and mounting points, as well as torn webbing and bent retractors, etc.
|
Replace after Deployment | Inspect & if Damaged, Replace Component (Even if Air Bag Did Not Deploy) | Comments | |||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
1Using new fasteners.
2Also referred to as diagnosis sensor unit.
Replace after any SRS component deploys.
3If any of the front air bags or seat belt
pre-tensioners have been activated: REPLACE the crash zone sensor
and bracket with new fasteners.
4Replace front seat back assembly following
deployment of side air bag.
5On the side of impact.
6Following deployment of driver’s
side air bag module.
7Confirm seat belt pretensioner deployment
using CONSULT tester.
8Replace integrated type instrument panel
following passenger’s side air bag module deployment.
9Inspect all seat belt assemblies. Replace
all seat belt assemblies in use during a collision, unless collision
was minor and belts, retractors and buckles show no damage and continue
to operate properly. Inspect carefully for damage to anchor bolts,
guides and mounting points, as well as torn webbing and bent retractors, etc.
|
Replace after Deployment | Inspect & if Damaged, Replace Component (Even if Air Bag Did Not Deploy) | Comments | |||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
1Using new fasteners.
2Also referred to as diagnosis sensor unit.
Replace after any SRS component deploys.
3If any of the front air bags or seat belt
pre-tensioners have been activated: REPLACE the crash zone sensor
and bracket with new fasteners.
4Replace front seat back assembly following
deployment of side air bag.
5On the side of impact.
6Following deployment of driver’s
side air bag module.
7Confirm seat belt pretensioner deployment
using CONSULT tester.
8Replace integrated type instrument panel
following passenger’s side air bag module deployment.
9Inspect all seat belt assemblies. Replace
all seat belt assemblies in use during a collision, unless collision
was minor and belts, retractors and buckles show no damage and continue
to operate properly. Inspect carefully for damage to anchor bolts,
guides and mounting points, as well as torn webbing and bent retractors, etc.
|
Replace after Deployment | Inspect & if Damaged, Replace Component (Even if Air Bag Did Not Deploy) | Comments | |||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
1Using new fasteners.
2Also referred to as diagnosis sensor unit.
Replace after any SRS component deploys.
3If any of the front air bags or seat belt
pre-tensioners have been activated: REPLACE the crash zone sensor
and bracket with new fasteners.
4Replace front seat back assembly following
deployment of side air bag.
5On the side of impact.
6Following deployment of driver’s
side air bag module.
7Confirm seat belt pretensioner deployment
using CONSULT tester.
8Replace integrated type instrument panel
following passenger’s side air bag module deployment.
9Inspect all seat belt assemblies. Replace
all seat belt assemblies in use during a collision, unless collision
was minor and belts, retractors and buckles show no damage and continue
to operate properly. Inspect carefully for damage to anchor bolts,
guides and mounting points, as well as torn webbing and bent retractors, etc.
|
Replace after Deployment | Inspect & if Damaged, Replace Component (Even if Air Bag Did Not Deploy) | Comments | |||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
1Using new fasteners.
2Also referred to as diagnosis sensor unit.
Replace after any SRS component deploys.
3If any of the front air bags or seat belt
pre-tensioners have been activated: REPLACE the crash zone sensor
and bracket with new fasteners.
4Replace front seat back assembly following
deployment of side air bag.
5On the side of impact.
6Following deployment of driver’s
side air bag module.
7Confirm seat belt pretensioner deployment
using CONSULT tester.
8Replace integrated type instrument panel
following passenger’s side air bag module deployment.
9Inspect all seat belt assemblies. Replace
all seat belt assemblies in use during a collision, unless collision
was minor and belts, retractors and buckles show no damage and continue
to operate properly. Inspect carefully for damage to anchor bolts,
guides and mounting points, as well as torn webbing and bent retractors, etc.
|
Replace after Deployment | Inspect & if Damaged, Replace Component (Even if Air Bag Did Not Deploy) | Comments | |||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
1Using new fasteners.
2Also referred to as diagnosis sensor unit.
Replace after any SRS component deploys.
3If any of the front air bags or seat belt
pre-tensioners have been activated: REPLACE the crash zone sensor
and bracket with new fasteners.
4Replace front seat back assembly following
deployment of side air bag.
5On the side of impact.
6Following deployment of driver’s
side air bag module.
7Confirm seat belt pretensioner deployment
using CONSULT tester.
8Replace integrated type instrument panel
following passenger’s side air bag module deployment.
9Inspect all seat belt assemblies. Replace
all seat belt assemblies in use during a collision, unless collision
was minor and belts, retractors and buckles show no damage and continue
to operate properly. Inspect carefully for damage to anchor bolts,
guides and mounting points, as well as torn webbing and bent retractors, etc.
|
Replace after Deployment | Inspect & if Damaged, Replace Component (Even if Air Bag Did Not Deploy) | Comments | |||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
1Using new fasteners.
2Replace after any SRS component deploys.
3If any of the front air bags or seat belt
pre-tensioners have been activated: REPLACE the crash zone sensor
and bracket with new fasteners.
4On the side of impact.
5Replace front seat back assembly following
deployment of side air bag.
6Replace door finisher on models with door
mounted curtain air bag modules after deployment.
7Repair center pillar inner if damaged.
8Following deployment of driver-side air
bag module.
9Confirm seat belt pretensioner deployment
using CONSULT tester.
10Replace integrated type instrument panel
following passenger’s side air bag module deployment.
11Inspect all seat belt assemblies. Replace
all seat belt assemblies in use during a collision, unless collision
was minor and belts, retractors and buckles show no damage and continue
to operate properly. Inspect carefully for damage to anchor bolts,
guides and mounting points, as well as torn webbing and bent retractors, etc.
|
Replace after Deployment | Inspect & if Damaged, Replace Component (Even if Air Bag Did Not Deploy) | Comments | |||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
1Using new fasteners.
2Also referred to as diagnosis sensor unit.
Replace after any SRS component deploys.
3If any of the front air bags or seat belt
pre-tensioners have been activated: REPLACE the crash zone sensor
and bracket with new fasteners.
4Replace front seat back assembly following
deployment of side air bag.
5On the side of impact.
6Following deployment of driver’s
side air bag module.
7Confirm seat belt pretensioner deployment
using CONSULT tester.
8Following passenger’s side air
bag module deployment.
9Inspect all seat belt assemblies. Replace
all seat belt assemblies in use during a collision, unless collision
was minor and belts, retractors and buckles show no damage and continue
to operate properly. Inspect carefully for damage to anchor bolts,
guides and mounting points, as well as torn webbing and bent retractors, etc.
|
Replace after Deployment | Inspect & if Damaged, Replace Component (Even if Air Bag Did Not Deploy) | Comments | |||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
1Using new fasteners.
2Also referred to as diagnosis sensor unit.
Replace after any SRS component deploys.
3If any of the front air bags or seat belt
pre-tensioners have been activated: REPLACE the crash zone sensor
and bracket with new fasteners.
4Replace front seat back assembly following
deployment of side air bag.
5On the side of impact.
6Following deployment of driver’s
side air bag module.
7Confirm seat belt pretensioner deployment
using CONSULT tester.
8Replace integrated type instrument panel
following passenger’s side air bag module deployment.
9Inspect all seat belt assemblies. Replace
all seat belt assemblies in use during a collision, unless collision
was minor and belts, retractors and buckles show no damage and continue
to operate properly. Inspect carefully for damage to anchor bolts,
guides and mounting points, as well as torn webbing and bent retractors, etc.
|
Replace after Deployment | Inspect & if Damaged, Replace Component (Even if Air Bag Did Not Deploy) | Comments | |||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
1Using new fasteners.
2Also referred to as diagnosis sensor unit.
Replace after any SRS component deploys.
3If any of the front air bags or seat belt
pre-tensioners have been activated: REPLACE the crash zone sensor
and bracket with new fasteners.
4Replace front seat back assembly following
deployment of side air bag.
5On the side of impact.
6Following deployment of driver’s
side air bag module.
7Confirm seat belt pretensioner deployment
using CONSULT tester.
8Replace integrated type instrument panel
following passenger’s side air bag module deployment.
9Inspect all seat belt assemblies. Replace
all seat belt assemblies in use during a collision, unless collision
was minor and belts, retractors and buckles show no damage and continue
to operate properly. Inspect carefully for damage to anchor bolts,
guides and mounting points, as well as torn webbing and bent retractors, etc.
|
Replace after Deployment | Inspect & if Damaged, Replace Component (Even if Air Bag Did Not Deploy) | Comments | |||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
1Using new fasteners.
2Also referred to as diagnosis sensor unit.
Replace after any SRS component deploys.
3If any of the front air bags or seat belt
pre-tensioners have been activated: REPLACE the crash zone sensor
and bracket with new fasteners.
4Replace front seat back assembly following
deployment of side air bag.
5On the side of impact.
6Following deployment of driver’s
side air bag module.
7Confirm seat belt pretensioner deployment
using CONSULT tester.
8Replace integrated type instrument panel
following passenger’s side air bag module deployment.
9Inspect all seat belt assemblies. Replace
all seat belt assemblies in use during a collision, unless collision
was minor and belts, retractors and buckles show no damage and continue
to operate properly. Inspect carefully for damage to anchor bolts,
guides and mounting points, as well as torn webbing and bent retractors, etc.
|
Replace after Deployment | Inspect & if Damaged, Replace Component (Even if Air Bag Did Not Deploy) | Comments | |||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
1Using new fasteners.
2Also referred to as diagnosis sensor unit.
Replace after any SRS component deploys.
3If any of the front air bags or seat belt
pre-tensioners have been activated: REPLACE the crash zone sensor
and bracket with new fasteners.
4Replace front seat back assembly following
deployment of side air bag.
5On the side of impact.
6Following deployment of driver’s
side air bag module.
7Confirm seat belt pretensioner deployment
using CONSULT tester.
8Replace integrated type instrument panel
following passenger’s side air bag module deployment.
9Inspect all seat belt assemblies. Replace all seat belt
assemblies in use during a collision, unless collision was minor
and belts, retractors and buckles show no damage and continue to
operate properly. Inspect carefully for damage to anchor bolts,
guides and mounting points, as well as torn webbing and bent retractors, etc.
10If the pop-up roll bar has deployed: Replace
pop-up roll bar assemblies and pop-up roll bar covers. Install with
new fasteners.
|
Replace after Deployment | Inspect & if Damaged, Replace Component (Even if Air Bag Did Not Deploy) | Comments | |||||||||||||||||||||||||||
|
|
||||||||||||||||||||||||||||
1Using new fasteners.
2Also referred to as diagnosis sensor unit.
Replace after any SRS component deploys.
3If any of the front air bags or seat belt
pre-tensioners have been activated: REPLACE the crash zone sensor
and bracket with new fasteners.
4Replace front seat back assembly following
deployment of side air bag. If the rear side air bag has deployed:
REPLACE rear seatback assembly.
5On the side of impact.
6Following deployment of driver’s
front air bag module.
7Confirm seat belt pretensioner deployment
using CONSULT tester.
8Replace integrated type instrument panel
following passenger’s side air bag module deployment.
9Inspect all seat belt assemblies. Replace all seat belt
assemblies in use during a collision, unless collision was minor
and belts, retractors and buckles show no damage and continue to
operate properly. Inspect carefully for damage to anchor bolts,
guides and mounting points, as well as torn webbing and bent retractors, etc.
10If the pop-up roll bar has deployed: Replace
pop-up roll bar assemblies and pop-up roll bar covers. Install with
new fasteners.
11If the door-mounted curtain air bag module
has deployed: Replace the door finisher and door-mounted curtain
air bag module. Install with new fasteners.
12If the front center air bag has deployed:
REPLACE the front seatback assembly RH.
13On a side and/or rollover collision,
check the center inner pillar on the collision side for damage (dents,
cracks, deformation, etc.). If damaged ? REPAIR the center inner
pillar.
|
Replace after Deployment | Inspect & if Damaged, Replace Component (Even if Air Bag Did Not Deploy) | Comments | |||||||||||||||||||||||||||
|
|
|
|||||||||||||||||||||||||||
1Using new fasteners.
2Also referred to as diagnosis sensor unit.
Replace after any SRS component deploys.
3If any of the front air bags or seat belt
pre-tensioners have been activated: REPLACE the crash zone sensor
and bracket with new fasteners.
4Replace front seat back assembly following
deployment of side air bag. Replace right front seat back assembly
following deployment of front center airbag.
5If the rear side air bag has deployed: REPLACE
rear seatback assembly.
6On the side of impact.
7Following deployment of driver’s
side air bag module.
8Confirm seat belt pretensioner deployment
using CONSULT tester.
9Replace integrated type instrument panel
following passenger’s side air bag module and/or
knee air bag module deployment.
10Inspect all seat belt assemblies. Replace
all seat belt assemblies in use during a collision, unless collision
was minor and belts, retractors and buckles show no damage and continue
to operate properly. Inspect carefully for damage to anchor bolts,
guides and mounting points, as well as torn webbing and bent retractors, etc.
11If the pop-up roll bar has deployed: Replace
pop-up roll bar assemblies and pop-up roll bar covers. Install with
new fasteners.
12If the door-mounted curtain air bag module
has deployed: Replace the door finisher and door-mounted curtain
air bag module. Install with new fasteners.
13If the air bag has NOT been activated: Remove
air bag module. Check harness cover and connectors for damage, terminals
for deformities, and harness for binding. Install air bag module
to check fit with the instrument panel. If no damage is found, reinstall
with new fasteners. If damaged REPLACE. Install air bag modules
with new fasteners.
14If the pre-tensioners have NOT been activated:
Remove seat belt pre-tensioner assembly. Check harness cover and
connectors for damage, terminals for deformities, and harness for
binding. Check belts for damage and anchors for loose mounting.
Check retractor for smooth operation. Check seat belt adjuster for damage.
Check for deformities of the center pillar inner. If the center
pillar inner has no damage, REPLACE the seat belt pre-tensioner
assembly with new fasteners. If no damage is found, reinstall seat
belt pre-tensioner assembly with new fasteners. If damaged REPLACE.
Install the seat belt pre-tensioner assembly with new fasteners.
15Remove passenger seat assembly. Check control
unit case for dents, cracks of deformities. Check connectors for
damage and terminals for deformities. Check seat frame and cushion
pan for dents or deformities. If no damage is found, reinstall seat
with new fasteners. If damaged REPLACE seat cushion assembly with new
fasteners. Perform zero point reset function after front passenger
seat is installed in the vehicle and all bolts are tightened to
specification.
16If the front air bags or seat belt pre-tensioners
have NOT been activated: Remove the crash zone sensor. Check harness
connectors for damage, terminals for deformities, and harness for
binding. Check for visible signs of damage (dents, cracks, deformation)
of the crash zone sensor and bracket. Install the crash zone sensor
to check fit. If no damage is found, reinstall with new fasteners.
If damaged REPLACE the crash zone sensor and bracket with new fasteners.
17If none of the SRS components have been
activated: Remove the door (satellite) sensor (LH or RH) on the
collision side. Check harness connectors for damage, terminals for
deformities, and harness for binding. Check for visible signs of
damage (dents, cracks, deformation) of the door (satellite) sensor
(LH or RH). Install the door (satellite) sensor (LH or RH) to check
fit. If no damage is found, reinstall the door (satellite) sensor
(LH or RH) with new fasteners. If damaged REPLACE the door (satellite)
sensor (LH or RH) with new fasteners.
|
Replace after Deployment | Inspect & if Damaged, Replace Component (Even if Air Bag Did Not Deploy) | Comments | |||||||||||||||||||||||||||
|
|
|
|||||||||||||||||||||||||||
1Using new fasteners.
2Also referred to as diagnosis sensor unit.
Replace after any SRS component deploys.
3If any of the front air bags or seat belt
pre-tensioners have been activated: REPLACE the crash zone sensor
and bracket with new fasteners.
4Replace front seat back assembly following
deployment of side air bag. Replace right front seat back assembly
following deployment of front center airbag.
5If the rear side air bag has deployed: REPLACE
rear seatback assembly.
6On the side of impact.
7Following deployment of driver’s
side air bag module.
8If either the driver or passenger seat belt
pre-tensioner has been activated: REPLACE all seat belt pre-tensioner
assemblies with new fasteners. Confirm seat belt pre-tensioner activation
using CONSULT only.
9Replace integrated type instrument panel
following passenger’s side air bag module and/or
knee air bag module deployment.
10Inspect all seat belt assemblies. Replace
all seat belt assemblies in use during a collision, unless collision
was minor and belts, retractors and buckles show no damage and continue
to operate properly. Inspect carefully for damage to anchor bolts,
guides and mounting points, as well as torn webbing and bent retractors, etc.
11If the pop-up roll bar has deployed: Replace
pop-up roll bar assemblies and pop-up roll bar covers. Install with
new fasteners.
12If the door-mounted curtain air bag module
has deployed: Replace the door finisher and door-mounted curtain
air bag module. Install with new fasteners. If the door-mounted
curtain air bag LH has NOT deployed: When removing door-mounted
curtain air bag module from door finisher, never reuse door finisher.
13If the air bag has NOT been activated: Remove
air bag module. Check harness cover and connectors for damage, terminals
for deformities, and harness for binding. Install air bag module
to check fit with the instrument panel. If no damage is found, reinstall
with new fasteners. If damaged REPLACE. Install air bag modules
with new fasteners.
14If the pre-tensioners have NOT been activated:
Remove seat belt pre-tensioner assembly. Check harness cover and
connectors for damage, terminals for deformities, and harness for
binding. Check belts for damage and anchors for loose mounting.
Check retractor for smooth operation. Check seat belt adjuster for damage.
Check for deformities of the center pillar inner. If no damage is
found, reinstall seat belt pre-tensioner assembly with new fasteners.
f damaged REPLACE. Install the seat belt pre-tensioner assembly
with new fasteners.
15Remove passenger seat assembly. Check control
unit case for dents, cracks of deformities. Check connectors for
damage and terminals for deformities. Check seat frame and cushion
pan for dents or deformities. If no damage is found, reinstall seat
with new fasteners. If damaged REPLACE seat cushion assembly with new
fasteners. Perform zero point reset function after front passenger
seat is installed in the vehicle and all bolts are tightened to
specification.
16If the front air bags or seat belt pre-tensioners
have NOT been activated: Remove the crash zone sensor. Check harness
connectors for damage, terminals for deformities, and harness for
binding. Check for visible signs of damage (dents, cracks, deformation)
of the crash zone sensor and bracket. Install the crash zone sensor
to check fit. If no damage is found, reinstall with new fasteners.
If damaged REPLACE the crash zone sensor and bracket with new fasteners.
17If none of the SRS components have been activated: Remove
the door (satellite) sensor (LH or RH) on the collision side. Check
harness connectors for damage, terminals for deformities, and harness
for binding. Check for visible signs of damage (dents, cracks, deformation)
of the door (satellite) sensor (LH or RH). Install the door (satellite)
sensor (LH or RH) to check fit. If no damage is found, reinstall
the door (satellite) sensor (LH or RH) with new fasteners. If damaged
REPLACE the door (satellite) sensor (LH or RH) with new fasteners.
18If the curtain air bag LH or RH has NOT
deployed: Check for visible signs of damage (dents, tears, deformation,
etc.) of the center pillar on the collision side. If damaged - Remove
the curtain air bag module. Check for visible signs of damage (tears
etc.) of the curtain air bag module. Check harness and connectors
for damage, and terminals for deformities. If no damage is found,
reinstall the curtain air bag module with new fasteners. If damaged
- REPLACE the curtain air bag module with new fasteners.
|
Replace after Deployment | Inspect & if Damaged, Replace Component (Even if Air Bag Did Not Deploy) | Comments | |||||||||||||||||||||||||||
|
|
|
|||||||||||||||||||||||||||
1Using new fasteners.
2Also referred to as diagnosis sensor unit.
Replace after any SRS component deploys.
3If any of the front air bags or seat belt
pre-tensioners have been activated: REPLACE the crash zone sensor
and bracket with new fasteners.
4Replace front seat back assembly following
deployment of side air bag. Replace right front seat back assembly
following deployment of front center airbag.
5If the rear side air bag has deployed: REPLACE
rear seatback assembly.
6On the side of impact.
7Following deployment of driver’s side air bag module.
8Confirm seat belt pretensioner deployment
using CONSULT tester.
9Replace integrated type instrument panel
following passenger’s side air bag module and/or
knee air bag module deployment.
10Inspect all seat belt assemblies. Replace
all seat belt assemblies in use during a collision, unless collision
was minor and belts, retractors and buckles show no damage and continue
to operate properly. Inspect carefully for damage to anchor bolts,
guides and mounting points, as well as torn webbing and bent retractors, etc.
11If the pop-up roll bar has deployed: Replace
pop-up roll bar assemblies and pop-up roll bar covers. Install with
new fasteners.
12If the door-mounted curtain air bag module
has deployed: Replace the door finisher and door-mounted curtain
air bag module. Install with new fasteners.
13If the air bag has NOT been activated: Remove
air bag module. Check harness cover and connectors for damage, terminals
for deformities, and harness for binding. Install air bag module
to check fit with the instrument panel. If no damage is found, reinstall
with new fasteners. If damaged REPLACE. Install air bag modules
with new fasteners.
14If the pre-tensioners have NOT been activated:
Remove seat belt pre-tensioner assembly. Check harness cover and
connectors for damage, terminals for deformities, and harness for
binding. Check belts for damage and anchors for loose mounting.
Check retractor for smooth operation. Check seat belt adjuster for damage.
Check for deformities of the center pillar inner. If no damage is
found, reinstall seat belt pre-tensioner assembly with new fasteners.
If damaged REPLACE. Install the seat belt pre-tensioner assembly
with new fasteners.
15Remove passenger seat assembly. Check control
unit case for dents, cracks of deformities. Check connectors for
damage and terminals for deformities. Check seat frame and cushion
pan for dents or deformities. If no damage is found, reinstall seat
with new fasteners. If damaged REPLACE seat cushion assembly with new
fasteners. Perform zero point reset function after front passenger
seat is installed in the vehicle and all bolts are tightened to
specification.
16If the front air bags or seat belt pre-tensioners
have NOT been activated: Remove the crash zone sensor. Check harness
connectors for damage, terminals for deformities, and harness for
binding. Check for visible signs of damage (dents, cracks, deformation)
of the crash zone sensor and bracket. Install the crash zone sensor
to check fit. If no damage is found, reinstall with new fasteners.
If damaged REPLACE the crash zone sensor and bracket with new fasteners.
17If none of the SRS components have been activated: Remove
the door (satellite) sensor (LH or RH) on the collision side. Check
harness connectors for damage, terminals for deformities, and harness
for binding. Check for visible signs of damage (dents, cracks, deformation)
of the door (satellite) sensor (LH or RH). Install the door (satellite)
sensor (LH or RH) to check fit. If no damage is found, reinstall
the door (satellite) sensor (LH or RH) with new fasteners. If damaged
REPLACE the door (satellite) sensor (LH or RH) with new fasteners.
|